Stronger Flow
Stronger Flow | Pipe Upgrades | Plumbing | Halls
When the taps in Halls need the muscle to power showers, dishwashers, and heating systems all at once, HEP’s stronger flow plumbing solutions deliver. Our expert engineers specialise in pipe upgrades that replace tired, narrow lines with modern, high-capacity piping, boosting water pressure and minimising the risk of leaks. From student residences to historic halls, we work tidily and fast, so daily life keeps moving even while we install the new backbone of your building’s water network.
Choose HEP and enjoy smoother showers, quicker fills, and a system built to last decades. We source corrosion-resistant materials, provide transparent quotes, and back every project with a watertight guarantee. Ready to feel the difference? Book an on-site assessment today and let HEP turn your plumbing into a quiet, powerful flow you can rely on.
FAQs
Why should I consider upgrading my old pipes to improve water flow?
Older galvanized steel or corroded copper lines tend to build up mineral deposits and rust, which shrink the inside diameter of the pipe and act like a bottleneck. The result is weak shower pressure, slow-filling appliances, and uneven flow when more than one fixture runs at once. Re-piping with modern, smooth-walled materials immediately restores the full interior diameter, allowing water to move with far less resistance and giving you stronger, more consistent pressure throughout the house.
What pipe materials do you recommend for a stronger flow in Halls homes?
For most residential upgrades we suggest Type L copper, PEX-A, or ASTM F1960 (cold-expanded) Uponor PEX. Type L copper is durable and naturally antimicrobial, while PEX-A offers flexible runs with fewer fittings, which means fewer points of restriction. Both materials have larger internal diameters than aging galvanized lines of the same nominal size, so you get an immediate improvement in flow. In high-demand situations—such as multi-story homes with spa tubs—we may combine a three-quarter-inch trunk line in PEX with half-inch branches to fixtures to keep pressure balanced.
Will a pipe upgrade disrupt my daily water service, and how long does the project usually take?
We isolate sections of your plumbing so the entire house is not out of service at once. Water is typically shut off only during the final tie-in for each level, usually 2–4 hours. A full re-pipe on a 2-bath, 1,800 sq ft home in Halls takes 1 –3 days, depending on crawl-space or slab foundation access. We protect floors and walls with drop cloths, use dust-minimizing drywall cuts, and clean up each evening so you can remain in the home during the process.
How can I tell if poor water flow is caused by my pipes or by the municipal supply?
First, test the static pressure at an exterior hose bib with a simple pressure gauge; Halls Utilities usually provides 45–70 psi. If you see good static pressure but pressure drops sharply when two fixtures are opened, the issue is almost always inside the house—restricted or undersized piping. Visible corrosion at shut-off valves, discolored water on first draw, and noisy pipes are further clues. If static pressure is low at the gauge, we can confirm with Halls Utilities and, if needed, install a booster pump rather than re-pipe.
Are pipe upgrades in older Halls homes compliant with local building codes?
Yes. We pull the required Shelby County (or Lauderdale County for Halls, TN) plumbing permits, follow the 2021 International Residential Code, and schedule rough-in and final inspections. All new piping is pressure-tested to 100 psi for 15 minutes in front of the inspector. We also install code-mandated pressure-reducing valves if static pressure exceeds 80 psi and dielectric unions when transitioning from copper to steel components, ensuring full compliance and long-term protection against electrolysis.
What is the cost range for a stronger-flow pipe upgrade, and do you offer financing?
Pricing depends on home size, number of fixtures, crawl-space vs slab access, and material choice. In Halls, a typical 2-bath re-pipe with PEX-A starts around $4,500, while a similar job in Type L copper averages $6,500–$7,200. Larger homes or those with extensive drywall repair can exceed $10,000. We provide free on-site assessments, a written fixed price, and multiple payment options, including 12-month same-as-cash and low-interest plans up to 60 months through our partner financing program.